Bosch Rexroth Ricambi per Automazione Industriale

WT plate VFplus 65

SZ 5 Leg Set - Leg set for general applications - Extruded aluminum profiles - Height-adjustable bases - Suitable for the construction of high-load conveyor sections in conjunction with ST 5/... conveyor units - Lowest transport level that can be implemented (at the lowest foot setting 35 mm):ST 5/XH = 425.5 mmST 5/H = 335.5 mm

SZ 5/U Leg Set - Leg set for multi-level sections - Extruded aluminum profiles - Height-adjustable bases - Suitable for the construction of high-load conveyor sections in conjunction with ST 5/... conveyor units

SZ 5/OC Leg Set - Leg sets for Open Center sections - Extruded aluminum profiles - Height-adjustable bases - Suitable for the construction of high-load conveyor sections in conjunction with the ST 5/OC... conveyor units - Lowest possible transport level (with lowest possible foot setting of 35 mm): 335.5 mm

SZ 2/K-90 Leg Set - Leg set for K...-90 curves. - Installation location AO = 91: KE 2/90 - Installation location AO = 67: KU 2/R-90; KU 2/RO-90; KU 2/R-180; KU 2/RO-180

SZ 2/K-180 Leg Set - Leg set for K...-180 curves.

Cable duct with AL cover plate 80x80 - Cable duct pre-assembled (cover and bearing/support structure) - Usable length 3000 mm (delivered in 3100 mm lengths) - Cover can be secured with a self-tapping screw

Function-integrated profile 120x120 M12/- - Construction profiles with usable interior space for guiding cables and hoses - 2 parts (profile and cover) - Cover with hinge function on both sides - Concealed 10 mm groove for mounting socket strips or installation elements - Screw holes for mounting cover plates - Closed exterior - Mount for dividing strips and grounding cables - Mount for potential equalizer

Function-integrated profile 60x120 M12/M12 - Construction profiles with usable interior space for guiding cables and hoses - 2 parts (profile and cover) - Cover with hinge function on both sides - Concealed 10 mm groove for mounting socket strips or installation elements - Screw holes for mounting cover plates - Closed exterior - Mount for dividing strips and grounding cables - Mount for potential equalizer

BS 2/S belt section - The belt section is a ready-to-use conveyor section with built-in drive for the transportation of workpiece pallets in the longitudinal direction or for the transverse conveying of the workpiece pallet between parallel conveyor sections in conjunction with two HQ 2 lift transverse units. - Segmented belt section with the possibility of up to 3 additional cuts in the longitudinal profile - Connection with standard profile connectors - This allows flexible individual parts of the belt section to be removed - This also causes simpler handling and more efficient transportation of the belt sections - Accumulation operation possible - Conveyor medium: Toothed belt (suitable for use in an EPA) - Reversible operation possible - Can be combined with WT 2, WT 2/E, WT 2/F, WT 2/LS - Motor mounting on right, left or centrally (centrally on track widths of 240 mm and above) - Motor connection optionally with cable/plug (AT = S) or terminal box (AT = K) - Special models on request - Positioning of WTs in the area of the drive heads/return heads is not permitted.

The leg sets SZ 2/K-R carry a 90 ° or 180 ° KU 2/R… curve for b ≤ 160 mm with installation location 63.5. - Leg set for curves KU 2/R...-90 and KU 2/R...-180 for b ≤ 160 mm

Electrical transverse conveyor for connection of two longitudinal sections running in parallel with a small distance between conveyors. The electrical transverse conveyor EQ 1/TR is used for connecting two parallel longitudinal sections with a small distance between conveyors. It is also suitable for use in ESD applications. Accumulation operation not permitted. - Available for belt distances a = 60 mm or a = 135 mm - Lift cylinder – D = 25 mm - Total stroke: 13 mm - Conveyor medium: Toothed belt with mesh top, suitable for use in an EPA - Pneumatic equipment for 2 (top, center) or 3 (top, center, bottom) lift positions - Motor connection optionally with cable/plug (AT = S) or terminal box (AT = K) - Special models on request

PE 5/L-T positioning unit - Positioning a workpiece pallet in a manual or automated processing station in the transverse conveyor with high positioning accuracy requirements (±0.3 mm) - Can be used with all WT 5 workpiece pallets - Installation only possible from above - Lift over transport level: 5 mm - Positioning accuracy: ±0.3 mm in x and y direction - Permissible vertical process force with center load: up to 3500 N2) depending on WT weight, i.e. permitted load of 3500 N – weight WT = possible process force - Suitable for ST 5/XH and ST 5/H (not ST 5/XH‑FR or ST 5/H‑FR) - Compressed air connection: 5 ... 6 bar - Push in air connection: 8 mm - 2) If assembling in a ST 5/H section place legs directly in front of and behind the PE 5/L-T.

PE 5/L positioning unit - Positioning a workpiece pallet in a manual or automated processing station in the longitudinal conveyor with high positioning accuracy requirements (±0.3 mm) - Can be used with all WT 5 workpiece pallets - Installation only possible from above - Lift over transport level: 5 mm - Positioning accuracy: ±0.3 mm in x and y direction - Permissible vertical process force with center load: up to 3500 N2) depending on WT weight, i.e. permitted load of 3500 N – weight WT = possible process force - Suitable for ST 5/XH and ST 5/H (not ST 5/XH‑FR or ST 5/H‑FR) - Compressed air connection: 5 ... 6 bar - Push in air connection: 8 mm - 2) If assembling in a ST 5/H section place legs directly in front of and behind the PE 5/L.

Drive Module AS 2/C-100 - Drive for conveyor unit self-assembly - Conveyor medium: Flat top chain (where KA = A suitable for use in an EPA) - Motor mounting on right, left or centrally (centrally on track widths of 240 mm and above) - Motor connection: optionally with cable/plug or terminal box motor connection - Special models on request - Reversible operation not permitted - Use with medium accumulation loads - We strongly advise using the LU 2 automatic lubrication unit

Electrical transverse conveyor for branching workpiece pallets from a longitudinal section. The electric transverse conveyor EQ 1/TE is used as a branching transverse section. This can either be used as a dead end or, at the other end, transfer the workpiece pallets to an HQ or EQ 1/TR with built-in drive in order to feed them back into the longitudinal conveyor. The belt section and the lift transverse unit share a common motor. It is also suitable for use in ESD applications. Accumulation operation on the belt section and reversible operation are allowed. - Section load up to 30 kg - Lift cylinder – D = 25 mm - Total stroke: 13 mm - Motor mounting right (MA = R) or left (MA = L), with b = 160 mm also center (MA = M) - Conveyor medium: Toothed belt with mesh top, suitable for use in an EPA - Pneumatic equipment for 2 (top, center) or 3 (top, center, bottom) lift positions - Motor connection optionally with cable/plug (AT = S) or terminal box (AT = K) - Special models on request

Electrical transverse conveyor for connection of two longitudinal sections running in parallel with a distance between conveyors of more than 320 mm. The electrical transverse conveyor EQ 1/T is used for connecting two parallel longitudinal sections with a distance between conveyors of > = 320 mm. The belt section and the two lift transverse units share a common motor. It is also suitable for use in ESD applications. Accumulation operation on the belt section and reversible operation are allowed. - Section load up to 30 kg - Lift cylinder – D = 25 mm - Total stroke: 13 mm - Motor mounting right (MA = R) or left (MA = L), with b = 160 mm also center (MA = M) - Conveyor medium: Toothed belt with mesh top, suitable for use in an EPA - Pneumatic equipment for 2 (top, center) or 3 (top, center, bottom) lift positions - Motor connection optionally with cable/plug (AT = S) or terminal box (AT = K) - Special models on request

VE 5/D-301 stop gate - Damped stopping of one or more accumulating workpiece pallets at the defined workpiece pallet stop surfaces. - Pneumatic stop gate with steplessly adjustable damping. When the pressure is released the stop gate is closed by a spring and the workpiece pallet is stopped. - Compressed air connection: 5 ... 6 bar - Pneumatic connection, pushlock Ø 6 mm - Installation location AO = 1: Main section (stop gate is 35 mm eccentric) - Installation location AO = 2: Transverse section (stop gate is in the center, only applies for transverse section HQ 5)

BS 4/R-300 belt section - Longitudinal conveying of the workpiece pallet on segmented conveyor sections - Transverse conveying of the workpiece pallet between parallel conveyor sections (in conjunction with two lift transverse units HQ 4) - Ready-for-operation conveyor section - Section loads up to 700 kg in accumulation operation - Conveyor medium: Accumulation roller chain with steel support wheels - Automatic chain tensioning system - Steel chain guides - Suitable for reversible operation (RV = 1) to l = 2000 mm - Motor connection optionally with cable/plug (AT = S) or terminal box (AT = K)

VE 5/OCD-301 stop gate - Damped stopping of one or more accumulating workpiece pallets at the defined workpiece pallet stop surfaces. - Pneumatic stop gate with steplessly adjustable damping. When the pressure is released the stop gate is closed by a spring and the workpiece pallet is stopped. - Compressed air connection: 5 ... 6 bar - Pneumatic connection, pushlock Ø 6 mm - Installation location AO = 1: Main section (stop gate is 35 mm eccentric) - Installation location AO = 2: Transverse section (stop gate is in the center, only applies for transverse section HQ 5)