Lutron

Fan control (top) Slide up to on/increase speed, down to decrease/off. 3 quiet fan speeds designed to prevent motor hum (for use with only one ceiling paddle fan). Switch (bottom) Rocker switch turns light on/off.

Controls 600 W incandescent or halogen loads. Rocker switch returns light to light level indicated by slider. Slide up to brighten, down to dim.

Provides high-performance dimming for any compact fluorescent application. Offers continuous flicker-free dimming from 100% to 5 %, providing both energy savings and lighting flexibility. Compatible with Energi Savr Node with EcoSystem devices, GRAFIK Eye QS with EcoSystem connection, PowPak dimming module with EcoSystem connection, and Quantum systems, allowing for integration into an existing/planned EcoSystem lighting control system. Supports standard 3-wire line-voltage phase control technology. Programmed rapid start design ensures full-rated lamp life while dimming and cycling. Lamps turn on to any dimmed level without flashing to full brightness. Low harmonic distortion throughout the entire dimming range. Frequency of operation ensures that ballast does not interfere with infrared devices. Inrush current limiting circuitry eliminates circuit breaker tripping, switch arcing, and relay failure. Ultra-quiet operation. Protected from miswires of any input power to control lead, or from lamp leads to each other and/or ground. End-of-lamp-life protection circuitry ensures safe operation throughout entire lamp life. Nonvolatile memory restores all ballast settings after power failure. 100% compatible with all Lutron 3-wire fluorescent controls and EcoSystem digital controls. 100% performance tested at factory. Custom ballast factors available. Design tool and specifications can be found at www.lutron.com/ballasttool

Fan control (top) Slide up to on/increase speed, down to decrease/off. 3 quiet fan speeds designed to prevent motor hum (for use with only one ceiling paddle fan). Switch (bottom) Rocker switch turns light on/off.

Controls 8 A LED driver/3-wire fluorescent ballast dimmer loads. Slide up to brighten, down to dim.

Controls 1500 VA/1200 W magnetic low-voltage loads. Higher capacity dimmer, requires larger heat sink behind wallplate. Slide up to brighten, down to dim. Measures 4.56 in x 4.56 in. Requires large wallplate. Most can fit in a 1-gang electrical backbox.

Maximize the benefits of a lighting management system. Offers continuous, flicker-free 100 % to 10 % dimming; ideal for use where saving energy, increasing flexibility, and maximizing productivity are the goals of the lighting design. Integral sensor connection provides power for and responds to one occupancy sensor, one photo sensor, and one personal control input (infrared receiver or wallstation). Communicates status and sensor inputs over the EcoSystem digital link. Programmed rapid start design ensures full rated lamp life while dimming and cycling. Lamps turn on to any dimmed level without flashing to full brightness. Low harmonic distortion throughout the entire dimming range. Frequency of operation ensures that ballast does not interfere with infrared devices. End-of-lamp-life protection circuitry ensures safe operation throughout entire lamp life. Ultra-quiet operation. Non-volatile memory restores all ballast settings after power failure. Ballast maintain consistent light output for linear lamp lengths. Protected from miswires of any input to power to control lead, or from lamp leads to each other and/or ground. 100 % performance tested at factory. Custom ballast factors available. Design tool and specifications can be found at www.lutron.com/ballasttool

Controls 8 A 3-wire LED driver or fluorescent ballast loads. Paddle turns on/off. Slide up to brighten, down to dim.

Maximize the benefits of a lighting management system. Offers continuous, flicker-free 100 % to 10 % dimming; ideal for use where saving energy, increasing flexibility, and maximizing productivity are the goals of the lighting design. Integral sensor connection provides power for and responds to one occupancy sensor, one photo sensor, and one personal control input (infrared receiver or wallstation). Communicates status and sensor inputs over the EcoSystem digital link. Programmed rapid start design ensures full rated lamp life while dimming and cycling. Lamps turn on to any dimmed level without flashing to full brightness. Low harmonic distortion throughout the entire dimming range. Frequency of operation ensures that ballast does not interfere with infrared devices. End-of-lamp-life protection circuitry ensures safe operation throughout entire lamp life. Ultra-quiet operation. Non-volatile memory restores all ballast settings after power failure. Ballast maintain consistent light output for linear lamp lengths. Protected from miswires of any input to power to control lead, or from lamp leads to each other and/or ground. 100 % performance tested at factory. Custom ballast factors available. Design tool and specifications can be found at www.lutron.com/ballasttool

Controls 1000 W (800 W) magnetic low-voltage loads. Provides true dimming from each location (with companion dimmers).

2-button. Offers toggle functionality for any zone(s) or scenes in the system. Large, rounded buttons are easy to use. May be custom-configured for other functions. Works with Softswitch128 systems. Engraving and additional colors can be added to wallstations using button kits and faceplates, ordered separately.

Slide up to on, down to off. Works with all load types.