Bosch
PVA-CSK
Call station kit
- Get up to 90 days payment terms from 500+ suppliers
- Reselling discounts up to 40%!
Send request for price
1
Payment methods:
Specifications
- Country of Origin
- China
- Gross Weight (Kg)
- 0.77
- Net Weight (Kg)
- 0.68
- Length (M)
- 0.31
- Width (M)
- 0.25
- Height (M)
- 0.05
- Gross Weight (Lbs)
- 1.69756
- Net Weight (Lbs)
- 1.49915
- Length (In)
- 12.20473
- Width (In)
- 9.84252
- Height (In)
- 1.96851
- Material
- F.01U.298.726
Technical Specifications
- Nominal drive voltage
- 5 V by internal power supply for 5-V point lighting LEDs 24 V by external power supply for 24-V ring lighting LEDs
- Polar pattern
- Omnidirectional
- Sensitivity
- 3.1 mV/Pa ±4 dB
- Power LED (through screw-terminal connectors)
- Driven by MIX_PWR_LED (5 V DC or 24 V DC) 2 connections (VCC & open collector)
- Maximum supply current
- < 500 mA at 24 V
- Rated output impedance
- 500 Ω
- Internal power supply for lighting, without extensions
- < 150 mA/24 V < 200 mA/18 V
- Maximum drive current
- 20 mA for each LED
- Nominal current consumption
- < 300 mA
- Power rating
- 1.5 W
- Nominal level
- +6 dBu
- Signal-to-noise ratio (Mic and Line input, NF output)
- ≥ 60 dB
- Maximum power
- 2 W
- Nominal voltage
- 24 V DC (-10%/+30%)
- Maximum mic input level
- -21 dBu
- Nominal resistance
- 8 Ω
- Max current
- 100 mA
- LEDs connected to buttons (through screw-terminal connectors)
- This kit supports open drain outputs with max. 5 mA per output. Using the internal supply, a maximum of 100 mA can be sourced for all outputs. The kit also provides an external power supply for lighting LEDs of external normal buttons. 2 connections (VCC & open collector) are available for each LED connected to a button. In total, 38 LEDs share 10 common MIX_PWR_LED. These LEDs are supplied with 5 V DC using the internal power supply. The connected LEDs are supplied with 24 V DC using the external power supply. Each LED circuit has short-circuit protection.
- Included LCD display kit
- A flat ribbon cable connects the display to the call station kit mainboard. The ribbon cable length is +/- 300 mm
- Nominal current consumption for main power supply
- < 100 mA
- Buttons (through screw-terminal connectors)
- 5 pre-programmed 15 programmable zone/function buttons 3 supervised programmable optional emergency buttons 2 connections for each button; 23 buttons share 6 common VCCs (3V3 - DC) Each button has short circuit protection
- Maximum level
- +12 dBu
- Nominal operating voltage
- 3.5 V
- Others (through screw-terminal connectors)
- 1 audio source (line in) 1 supervised microphone input (eg. LBB9081) capsule and PTT button connection (input & VCC) with short-circuit protection. 1 loudspeaker connection, 1 additional +24 V DC power supply
- Fault LED (through screw-terminal connectors)
- Driven by MIX_PWR_LED (5 V DC or 24 V DC) 2 connections (VCC & open collector)
- Maximum voltage range
- 15–58 V DC
- External power supply for lighting, without extensions
- < 80 mA/24 V < 110 mA/18 V
- External connectors
- 1 call station bus connector (control data + audio + power supply, RJ-45) 1 EXT connector (RJ-12, e.g. for call station extension)
- NF output
- Balanced
- Maximum line input level
- +4 dBu
- Switch
- On/off with remote control contact
- CAN interface
- 10, 20, or 62.5 kbit/s
- Alarm LED (through screw-terminal connectors)
- Driven by MIX_PWR_LED (5 V DC or 24 V DC) 2 connections (VCC & open collector)
- Nominal drive current
- 5 mA for each LED
- Frequency response
- 200–16,000 Hz, +0/-3 dB
Documents
Data Sheet
DownloadOther Categories
ActuatorsBlocksCables, Pipes & HosesCompressorsControlCouplings & FittingsCylinders & PistonsElectronicsFiltersHVACIndustrial PC's & HMIsLightingLinear techniqueMotorsPower SupplyPower TransmissionPumps & ValvesRenewable energyRoboticsSeals, Rings & ConnectorsSensors & Measuring DevicesTools and AccessoriesCNCOther