SMART1000RM2UL

Overview

UPC Code

037332213099

UPS Type

Line-Interactive

Output

Output Volt Amp Capacity (VA)

1000

Output kVA Capacity (kVA)

1.0

Output Watt Capacity (Watts)

800

Power Factor

0.8

Nominal Voltage Details

120v nominal output in battery mode

Frequency Compatibility

60 Hz

Output Voltage Regulation (Battery Mode)

+/- 5%

Load Management Receptacles

Two switchable two-outlet load banks

Output AC Waveform (AC Mode)

Pure Sine wave

Output AC Waveform (Battery Mode)

Pure Sine wave

Nominal Output Voltage(s) Supported

110V; 115V; 120V

Output Receptacles

(6) 5-15R

Individually Controllable Load Banks

Yes

Input

Rated input current (Maximum Load)

9.2A (120V)

Nominal Input Voltage(s) Supported

120V AC

UPS Input Connection Type

5-15P

UPS Input Cord Length (ft.)

10

Recommended Electrical Service

15A 120V

Input Phase

Single-Phase

Battery

Full Load Runtime (min.)

8.3 min. (800w)

Half Load Runtime (min.)

20 min. (400w)

DC System Voltage (VDC)

24

Battery Recharge Rate (Included Batteries)

2.7 hours from 10% to 90% (typical)

Expandable Runtime

No

Voltage Regulation

Voltage Regulation Description

Automatic voltage regulation (AVR) maintains line power operation with an input voltage range of 83 to 147

Overvoltage Correction

Input voltages between 127 and 147 are reduced by 12%

Undervoltage Correction

Input voltages between 83 and 107 are boosted by 12%

User Interface, Alerts & Controls

Front Panel LCD Display

Front panel LCD information and configuration screen offers detailed UPS and site power status and operating data, plus configuration of voltage, operating mode, alarm function and a variety of additional options (see manual for detailed LCD configuration and monitoring options)

Switches

3 pushbutton switches control OFF / ON power status, MODE selection and MUTE / ENTER control functions

Alarm Cancel Operation

Power-fail alarm can be temporarily silenced using alarm-cancel switch; silent mode alarm configuration option available

Audible Alarm

Audible alarm indicates UPS startup, power-failure, low-battery, overload, UPS fault and remote shutdown conditions

Surge / Noise Suppression

UPS AC Suppression Joule Rating

570

UPS AC Suppression Response Time

Instantaneous

EMI / RFI AC Noise Suppression

Yes

Physical

Cooling Method

Fan

Included Mounting Accessory Description

Included 4POSTRAILKIT mounting bracket enables installation in 4 post racks from 20.5 to 36 inches (521 to 914mm)

Installation Form Factors Supported with Included Accessories

4 post 19 inch rackmount

Installation Form Factors Supported with Optional Accessories

2 post rackmount ( 2POSTRMKITWM ); 2-4 post front rail rackmount ( UPSHDEARKIT ); 4 post rackmount short-depth ( 4POSTRAILKITWM ); Tower ( 2-9USTAND ); Wallmount ( 2POSTRMKITWM )

Minimum Required Rack Depth (inches)

15.5

Optional Mounting Accessory Notes

Optional 2-9USTAND enables upright tower UPS placement; 2POSTRMKITWM enables wall-mount and 2-post rackmount installation; 4POSTRAILKITWM enables installation in 4-post short-depth racks from 14.5 to 23.5 inches (368 to 597mm); UPSHDEARKIT enables installation in 2 or 4-post racks using front vertical rails only, without rear support

Primary Form Factor

Rackmount

Primary UPS Depth (mm)

318

Primary UPS Height (mm)

89

Primary UPS Width (mm)

441

Rack Height

2U

Shipping Dimensions (hwd / in.)

8.70 x 18.50 x 23.30

UPS Housing Material

Steel

UPS Power Module Dimensions (hwd, in.)

3.5 x 17.35 x 12.5

UPS Power Module Weight (kg)

7.39

UPS Power Module Weight (lbs.)

16.3

Environmental

Operating Temperature Range

+32 to +104 degrees Fahrenheit / 0 to +40 degrees Celsius

Storage Temperature Range

+5 to +122 degrees Fahrenheit / -15 to +50 degrees Celsius

Relative Humidity

Up to 95%, non-condensing

AC Mode BTU / Hr. (Full Load)

141

AC Mode Efficiency Rating (100% Load)

95%

Audible Noise

45.5 dBA maximum, front side 1m

Communications

Network Management Cards

SNMPWEBCARD ; TLNETCARD ; WEBCARDLX ; RELAYIOCARD

Network Monitoring Port Description

Supports detailed monitoring of UPS and site power conditions

Communications Cable

USB, DB9 and EPO cabling included

WatchDog Compatibility

Supports Watchdog application, OS and hard-reboot restart options for remote applications

Network UPS Tools Compatibility

NUT compatible. See the full list of Tripp Lite NUT compatible UPS systems at http://www.networkupstools.org/stable-hcl.html?manufacturer=Tripp Lite

Communications Interface

USB (HID enabled); DB9 Serial; EPO (emergency power off); Slot for SNMP/Web interface

Line / Battery Transfer

Transfer Time

4 milliseconds (AC to battery mode), 2 milliseconds (Battery to AC mode)

Low Voltage Transfer to Battery Power (Setpoint)

83

High Voltage Transfer to Battery Power (Setpoint)

147

Special Features

Grounding Lug

Back panel grounding lug

Cold Start (Startup in Battery Mode During a Power Failure)

Cold-start operation supported

Green Energy-Saving Features

Individually controllable load banks

Certifications

UPS Certifications

Meets FCC Part 15 Category B (EMI); ROHS (Restriction of Hazardous Substances); Tested to CSA (Canada); Tested to NOM (Mexico); Tested to UL1778 (USA)

UPS Certification Details

UL 1778: 2014 R8.15 (5TH EDITION); CAN/CSA-C22.2 No. 107.3-14

Warranty

Product Warranty Period (Worldwide)

5-year limited warranty

Connected Equipment Insurance (U.S., Canada & Puerto Rico)

$250,000 Ultimate Lifetime Insurance

Documents