LEAD-ALIG-100

Specifications for the TS100 PRO

Maximum Length

8,000 feet (2,438 meters) on certain cable types, 4,000 feet (1,220 meters) on most cable types, and 500 feet (152 meters) on cables with high loss. The tester shows -Err if the cable is too long to be correctly measured.

Representative Maximum Cable Length

8,000 feet (2,438 meters): CAT-3 Twisted Pair || 1,500 feet (457 meters): RG-174/U Coax || 8,000 feet (2,438 meters): CAT-5 Twisted Pair || 3,000 feet (900 meters): RG-6/U TV Coax || 6,000 feet (1,830 meters): 12/2 AC Wire

Minimum Length

No minimum length (can read a bridge tap at 0 feet/meters). Minimum non-zero reading is 2 feet or 1 meter.

Length Accuracy

±2 feet (±0. 6 m) for cables less than 10 feet (3 m) || ±5 feet (±2 m) for cables longer than 10 feet (3 m) and shorter than 200 feet (60 m) || +/-3%+/-5 feet (±2 m) for cables longer than 200 feet (60 m)

Distance to Bridge Tap

0 feet to 3,200 feet (975 meters)

Minimum Length of Bridge Tap

10% of the distance to the bridge tap. Dependent on the cable characteristics.

Measurement Rate

Maximum of 4 complete measurements per second, decreasing to 2 seconds per measurement based on cable size and uniformity.

VOP

Adjustable from 20 to 99, saved in flash memory.

Test Technology

Time Domain Reflectometry (TDR) with 100 Ω drive impedance, 6v maximum pulse height.

Cable Type

Virtually all two or more conductor cables.

Power

4 AA alkaline batteries.

Reverse Battery Protection

No damage to the tester will occur if the batteries are installed backwards.

Battery Life

35 hours (typical)

Low Battery Indication

LED display alternates between LO and bAtt when the battery voltage falls below 4. 5v.

Maximum Output Voltage

4 voltage peak

Maximum Isolation Voltage

250 volts RMS

Voltage Measurements

Accuracy: AC: +/-1%+/-2 volts (45 Hz to 65 Hz); DC: +/-1%+/-2 volts DC || Range: 0 volts AC to 115 volts AC; 0 volts DC to ±150 volts DC

High Voltage Detection

AC voltage detected to 115 volts; DC voltage detected to ±150 volts. || AC voltage ≥90 volts or DC voltage ≥100 volts causes high voltage warnings to show on the display

SmartTone® (5-tones) Range

7,000 feet (2,134 meters)

Toner Range

52,800 feet (16,093 meters)

Tone Injection

Approximately 1 kHz at an amplitude of 80% of battery voltage. Variable frequency and cadence. Tone characteristics change as cable condition changes to “normal-open” from any other condition.

Impedance Range

35 Ω to 330 Ω with auto-compensation within this range. Cables with impedances outside this range will not be properly tested and may produce erratic or incorrect readings.

Temperature Range

Storage: 32°F to 131°F (0°C to 55°C) || Operating: 32°F to 104°F (0°C to 40°C)

Humidity

Storage: 0% to 100% relative humidity || Operating: 20% to 80% relative humidity

Operating Humidity

50% maximum at 104°F (40°C ) || 80% maximum at 86°F (30°C )

Operating Altitude

9,843 ft max (3,000 m max)

Weight

1 lb (454 grams)

Dimensions

7. 4 in x 2. 7 in x 1. 4 in (18. 8 cm x 6. 9 cm x 3. 6 cm)

Safety

EMC: IEC/EN61326-1:2006 || IEC 61010-1:2010; N10140

Certifications and Compliance

Conforms to relevant European Union directives || IEC/EN61010-1 CAN/CSA-C22. 2 No. 1010. 1-92 + CSA-C22. 2 No. 1010. 1B-97, UL/ANSI 3111-1 || Conforms to relevant Australian standards