Czujniki i urządzenia pomiarowe

The RF630T ETSI On-Metal Transponder is designed to operate within the ISO 18000-6C framework, featuring a compact form factor of 21 x 21 mm. This device operates at a frequency range of 865 to 868 MHz as per ETSI regulations and is equipped with the NXP G2XM chip, which provides an EPC of 240 bits along with 64 bytes of additional memory. Constructed with a plastic housing, the transponder is rated with a maximum transmission range of 2000 mm, ensuring effective communication in various applications. It is suitable for environments that demand high durability, as evidenced by its IP68/IPX9K protection rating, making it resistant to dust and water ingress. The operating temperature range of this device spans from -25 to +85 degrees Celsius, allowing it to function reliably in a variety of conditions. This product is available with a minimum order quantity of 10 units.

The inductive standard sensors are tailored for reliable object detection in metal contexts. With a dimension of Ø 4 x 41 mm, these sensors are constructed for flush mounting and offer a sensing range of 1.5 mm. They utilize a PNP Normally open (NO) switching output and can operate at a switching frequency of up to 5000 Hz. Designed to endure challenging conditions, the sensors feature a stainless steel housing and a PBT sensing surface, ensuring durability against dirt and contamination. The operating voltage ranges from 10 to 30 VDC, and they function effectively in ambient temperatures between -25 °C and 70 °C. Compliance with IP67 standards guarantees protection against dust and water ingress. These sensors are equipped with a 3-pin M8x1-Male connector for seamless integration into existing systems. The inductive sensors also carry multiple approvals including cULus, CE, EAC, and WEEE, confirming their reliability and adherence to safety standards. A broad selection of over 500 preferred types is available globally for swift delivery, making these sensors a practical solution for various applications.

Consisting of a 1 A measuring transducer and a Rogowski coil with a 3 m signal line, this product, designated as PACT RCP-4000A-1A-D190, provides precise measurements of AC current in power applications. The Rogowski coil features a length of 600 mm and a diameter of 190 mm, enabling effective current sensing capabilities. Manufactured in Germany, this device is characterized by reinforced insulation compliant with IEC 61010-1 and is rated for overvoltage category III at 1000 V. Its accuracy is quantified with a typical measuring error of less than 1 % and a maximum transmission error of ≤ 0.5 %, ensuring reliable performance in various conditions. Designed for a wide frequency range of 45 Hz to 65 Hz, the current transformer can accurately detect harmonics below 2 kHz. The nominal supply voltage operates between 19.2 V DC and 30 V DC, with a maximum current consumption of 190 mA. The output signal is calibrated to provide 100 mV at 1000 A input under no-load conditions. With a robust construction, the Rogowski coil is protected to IP54, while the measuring transducer adheres to IP20. The operating temperature range for the measuring coil extends from -30 °C to 80 °C, and for the transducer, from -20 °C to 70 °C, making it suitable for diverse environmental conditions.

The XS6 M18 inductive proximity sensor is designed for general purpose applications with a cylindrical body measuring 74 mm in length. It operates within a voltage range of 12 to 48 V DC, providing enhanced functionality for various industrial tasks.Constructed with a nickel plated brass body, this sensor is both corrosion-resistant and non-magnetic, ensuring accurate performance even in the presence of magnetic interference. Its PPS sensing face enhances its reliability in detecting targets, with a nominal sensing distance of 8 mm.This device incorporates an M12 male connector for electrical connection and features a 3-wire wiring technique. It is suitable for flush mounting, allowing for versatile installation options. The sensor is equipped with 4 LED indicators for monitoring its operational status, aiding in setup and troubleshooting.With an IP67, IP69K rating, this sensor is built to withstand harsh environmental conditions, operating effectively in temperatures ranging from -25°C to +70°C. It supports a switching capacity of up to 200 mA DC and has overload and short-circuit protection for enhanced safety.Certification includes CSA and UL, confirming compliance with industry standards. The XS6 sensor is also noted for its low current consumption and quick response times, making it suitable for mobile equipment applications. For detailed regulatory compliance, it holds a Green Premium status and adheres to environmental directives.

The capacitive sensors for object detection operate using a linear electrical field, enabling the detection of solid objects such as wafers, PCBs, cartons, and bottles, as well as liquids through container walls or glass and plastic tubes with a maximum thickness of 4 mm. The model G10T4H-PSM40C-EP02 features a dimension of Ø 10 x 50 mm and is suitable for flush mounting.These sensors utilize a PNP normally open (NO) switching output, with a switching frequency of 100 Hz and a sensing range of 1-4 mm. The sensitivity can be adjusted to meet specific detection needs. Constructed from stainless steel (1.4301) with a PTFE sensing surface, they can withstand ambient temperatures ranging from -30 to 70 °C. The device operates at a voltage range of 12-35 VDC and is equipped with a 2.00 m PUR cable for connection. Compliance with CE, cULus, and WEEE standards is assured, and the product has an IP65 rating for protection against dust and water ingress.

The XUB series photoelectric sensor operates within a supply voltage range of 12V to 24V DC. Constructed with a PBT case, it is designed for direct surface or bracket mounting due to its outer thread and accompanying twin nuts. The sensor's PMMA lens ensures scratch resistance, while the VALOX® PBT casing enhances durability in high-temperature settings.With a nominal sensing distance of 0.6 m and a maximum sensing distance of 0.8 m, this device employs a diffuse detection system. It is equipped with a single yellow LED for status indication, providing immediate feedback on operational status. Rated for harsh environments, the sensor meets IP65, IP67, and IP69K protection standards, enabling operation in temperatures ranging from -25°C to +55°C.Additional features include a maximum delay response of 1 ms and a switching frequency of up to 500 Hz. The device also integrates double insulation for enhanced protection against electrical shocks. Compliance with CE, UL, and CSA standards assures suitability for various industrial applications. The environmental sustainability of this product is indicated by its Green Premium designation, while it remains compliant with RoHS directives.

Introducing the Safety Interlock Switch, a robust solution designed for safety-critical applications. This switch boasts a tumbler locking force of 1300 N, ensuring secure operation in even the most demanding environments. The plastic enclosure provides excellent durability and protection against harsh conditions.With support for up to 5 directions of approaches, this switch offers versatility and adaptability to suit your specific needs. It features M12 connectors and ASIsafe integrated channels, enabling seamless integration into existing systems.The switch includes monitoring capabilities for actuator 2 (NC/1 NO) and magnet 2 (NC/1 NO), providing real-time feedback on the system's status. For added convenience, it features a spring-locked escape release at the rear and an auxiliary release on the front.To complete your setup, consider ordering the matching separate Actuator 3SE5000-0AV0 (sold separately). This combination ensures optimal performance and reliability for your safety-critical applications.

The safety position switch is designed for robust applications with a locking force of 1300 N and supports five approaches. It features a plastic enclosure and a reliable M12 connector. This switch integrates ASIsafe technology, providing safety functions across Channel 1 and Channel 2 with two normally closed (NC) contacts.The switch operates with a magnet voltage of 24 V DC/AC and includes monitoring capabilities for both the actuator (2 NC/1 NO) and the magnet (2 NC/1 NO). Additionally, it is equipped with a spring-locked auxiliary release on the front for enhanced operational safety.With a degree of protection rated at IP66/IP67, this device is suitable for various environments. It operates effectively at ambient temperatures ranging from -25 °C and is compliant with the AS-Interface Safety at Work standards. Note that the matching separate actuator, 3SE5000-0AV0, must be ordered separately.

The inductive standard sensors facilitate effective object detection within metal environments. With a dimension of Ø 12 x 65 mm and an installation style of quasi-flush, these sensors are particularly suited for applications requiring minimal space. They operate in a sensing range of 8 mm and employ a PNP Normally Open (NO) switching output, achieving a switching frequency of 300 Hz.These sensors are constructed from brass with a nickel-plated surface protection, ensuring durability and resistance to contaminants. The sensing surface is made from LCP, enhancing reliability in challenging conditions. Connectivity is provided through a 4-pin M12x1 Male connector. The operational voltage ranges from 10 to 55 VDC, allowing for versatile integration into various systems.With an ambient temperature rating of 0-60 °C and an IP67 ingress protection class, these sensors are designed for robust performance. The broad availability of over 500 preferred types globally ensures prompt delivery and adaptability to different applications. The product is compliant with CE, EAC, and WEEE standards.

This analogue position sensor is designed with a cylindrical form factor and is housed in nickel-plated brass, offered in both M18 and M30 sizes. It delivers an output current ranging from 0 to 20 mA, ensuring precise measurement capabilities. The sensor can be complemented with a level amplifier relay S 183 and an analogue display to create comprehensive measuring systems.With a rated operational voltage of 17 to 27 VDC and an operational current up to 20 mA, this device is suitable for various applications. The sensor's linearity is maintained within ± 3% of full scale, providing repeat accuracy of ≤ 1%. It is engineered to operate within an ambient temperature range of -15° to +65°C and is protected against harsh conditions with an IP 67 rating, which corresponds to Nema ratings 1, 3, 4, 6, and 13.The construction features a body made of nickel-plated brass, while the front and back are crafted from thermoplastic polyester in blue and black respectively. Its durability is enhanced by a reverse polarity current limiter and a transient voltage withstand of ≤ 2 kV/0.5 J. The sensor's weight, including the 2 m cable made from grey PVC, is 85 g, and it requires a tightening torque of 17.5 Nm for secure installation. Compliance with CE marking confirms its adherence to safety and operational standards.

The MACX MCR-TS-I-OLP is a loop-powered temperature measuring transducer that facilitates the transmission of signals from up to two sensors, including RTD and thermocouple (TC) types, as well as voltage and resistance sensors. Operating within a current output range of 4 mA to 20 mA, it supports HART communication protocol version 7 with a transmission speed of 1200 Baud.This device features a temperature measuring range greater than 10 K for RTD sensors and a linear resistance measuring range from 10 Ω to 2000 Ω. It is designed to operate under Safety Integrity Level (SIL) 2 (IEC 61508) and has a systematic capability rating of 3, ensuring reliable performance in critical applications.With a compact design, the transducer measures 12.5 mm in width, 112.5 mm in height, and 113.7 mm in depth, and is suitable for mounting on a DIN rail. The device is rated for an ambient temperature range of -40 °C to 85 °C during operation and -40 °C to 100 °C for storage and transport, making it suitable for a variety of industrial environments. The degree of protection is IP20, which indicates it is suitable for indoor use.For connection, it employs a screw method with a conductor cross-section ranging from 0.2 mm² to 2.5 mm² for both rigid and flexible conductors. The maximum current output can reach up to 23 mA with a load calculation based on the formula (UL - 11 V) / 0.023 A. The device is manufactured in Germany and includes an LED status display for operational feedback.

The photoelectric sensor from the XU range is designed for applications requiring precise detection capabilities. With dimensions of 92mm x 77mm, this compact device is constructed from durable plastic and utilizes an M12 connector for electrical connection. The sensor employs a diffuse detection system with adjustable background suppression and is capable of transmitting infrared signals.Configured with programmable PNP or NPN outputs, it supports both normally open (NO) and normally closed (NC) functions. With a nominal sensing distance of 2 meters, it excels in applications involving wrapping and outer wrapping. The device operates on a 3-wire system and is rated for a supply voltage between 10 and 36 VDC, accommodating reverse polarity protection.In terms of performance, the sensor consumes a no-load current of 35 mA, with a switching frequency of up to 150 Hz. The built-in status LEDs indicate power supply, instability, and output state, enhancing operational visibility. The sensor maintains a maximum voltage drop of less than 1.5 V in the closed state and has a solid-state output type.With robust certifications including CE, CSA, and UL, this sensor is rated for an ambient operating temperature range of -25 to 55 °C and can withstand vibrations of 7 gn at 10-55 Hz as per IEC 60068-2-6 standards. Additionally, it is designed for high shock resistance of 10 gn for 11 ms according to IEC 60068-2-27, and offers an IP65 degree of protection with double insulation, making it suitable for challenging environments.

The Photoelectric Sensor XUX is designed for versatile applications, featuring a supply voltage range of 24 to 240 V AC/DC. Constructed from durable painted aluminium and polyamide, it is suitable for surface or bracket mounting via four fixing points. The sensor's PBT housing is built to withstand high temperatures, while the PMMA lens ensures scratch resistance for enhanced durability.This compact sensor measures 92 x 71 mm and is equipped with an infrared thru beam detection system capable of a nominal sensing distance of up to 60 m. It operates effectively in extreme conditions, with an ambient temperature range of -25°C to +55°C. The sensor also incorporates double insulation for increased safety against electrical shocks.For improved usability, a dual LED display indicates sensor status and beam stability, facilitating troubleshooting. The device is rated with an IP65 and IP67 protection class, making it suitable for challenging environments. Its electronic design allows for a switching frequency of up to 20 Hz and a maximum delay response of 25 ms, catering to various operational needs.Certification by CSA and UL ensures compliance with safety standards, while the product's current consumption remains low at 20 mA under no-load conditions.

The XS5 series presents a cylindrical inductive proximity sensor designed for non-contact detection of metallic objects. With a diameter of 6.5mm and a length of 42mm, this sensor is constructed from stainless steel grade 303, ensuring durability in industrial settings. It is equipped with an M8 connector for electrical connection and complies with the IP67 degree of protection as per IEC 60529, making it suitable for challenging environments.This sensor operates within a voltage range of 12 to 24 VDC and features a PNP output with a normally closed (NC) function. Its nominal sensing distance is 1.5mm, allowing for effective detection while minimizing wear on both the sensor and the detected objects, including fragile or freshly painted surfaces. The response time is rapid with a maximum delay of 0.1 ms, and it supports a switching frequency of up to 5000 Hz.Additionally, the sensor is designed to handle a switching capacity of up to 200 mA DC and has overload and short-circuit protection. The device is also environmentally friendly, marked as a Green Premium product, and meets various regulatory standards including CSA and UL certifications.

Introducing the Phoenix Contact NBC-M12MSD/ 1,0-93E/M12MSD Network Cable, a high-performance solution designed to meet the demands of modern industrial automation systems. This cable is equipped with advanced shielding technology for reliable data transmission at speeds up to 100 Mbps.The cable features a 4-position design and is compatible with Plug straight M12 / IP67, coding: D. It offers a cable length of 1 meter, ensuring flexibility in installation and use. The advanced shielding technology provides superior protection against electromagnetic interference (EMI), ensuring stable data transmission even in challenging environments.

The photoelectric receiver XUB is designed for use in demanding environments, with a robust PBT case that withstands high temperatures and harsh conditions. It operates in a range from -25°C to +55°C, ensuring reliability in extreme temperatures. This device features an infrared thru-beam emission and a nominal sensing distance of 15 m, requiring a compatible transmitter for optimal performance. With its cylindrical M18 design and a diameter of 18 mm, this receiver can be easily mounted on surfaces or brackets using its outer thread and twin nuts. The PMMA lens provides scratch resistance, enhancing the durability of the sensor. A single yellow LED indicates the output state, enabling straightforward status monitoring. This unit is equipped with a standard M12 connector, ensuring compatibility with existing cabling systems. Additional features include double insulation for increased protection against electrical shocks, and compliance with CSA, UL, and CE certifications. The receiver is also designed with a maximum delay response of 1 ms and can handle switching frequencies of up to 500 Hz, making it suitable for various industrial applications. The model adheres to environmental standards such as RoHS and is mercury-free, contributing to sustainable usage. For further details on environmental impact, refer to the provided disclosures.

The XUSL2E Type 2 Safety Light Curtain is specifically designed for detecting personnel in proximity to hazardous equipment. It employs a transmitter-receiver mechanism that generates two light beams at a protective height of 510 mm. This product is characterized by a PFHd reliability data of 1.71 x 10⁻⁸, ensuring dependable safety operation.Constructed with an aluminum casing, the product includes integral LEDs for local status indication. It can function independently or in conjunction with a compatible safety control unit. The system features two normally open solid-state PNP safety outputs (OSSDs) and adheres to category 2, performance level PL c, and SIL 1 requirements as specified in EN/ISO 13849-1, EN/IEC 61508, alongside Type 2 compliance per EN/IEC 61496-1 and EN/IEC 61496-2.Operating within a temperature range of -30°C to +55°C, the device supports selectable sensing distances of either 0 to 4 meters or 0 to 12 meters, determined by wiring. Additionally, the installation is facilitated by fixing brackets, and the product is equipped with an M12 connector for electrical connections.

The limit switch, categorized under the XC Standard range, operates with a linear movement of the operating head and is equipped with a spring return metal roller plunger. Designed for lateral approach in two directions, it supports a maximum actuation speed of 0.5 m/s.With a body made of plastic, this switch has dimensions of 30mm in width, 16mm in depth, and 70.4mm in height, weighing 0.08kg. The fixed PVR insulated cable enables electrical connections with a length of 1 meter. It is rated IP65 for dust and water resistance and IK04 for impact protection.This device is capable of withstanding a rated operational current of 1.5A at 240V AC and 0.1A at 250V AC, ensuring reliability across various industrial machine applications including packaging, materials handling, and food processing. It has a mechanical and electrical durability of 5 million operating cycles.Compliance with multiple standards such as CSA C22.2 No 14, UL 508, and EN/IEC 60947-5-1 ensures its suitability for various environments. The product also adheres to sustainability practices, being mercury-free and classified as a Green Premium product.

Universally configurable frequency transducer for converting frequency (Hz/rpm) and PWM signals into standard signals. Sensor voltages greater than 8.2 V DC are possible in combination with MINI MCR-2-SPS 1033202. Screw connection technology.

The XUSL Type 4 Safety Light Curtain is specifically designed for detecting the presence of hands in hazardous areas, ensuring operator safety around machinery. It employs a transmitter-receiver system that generates 16 light beams, effectively covering a protected height of 310 mm.This device is characterized by its PFHD reliability data of 8.2 x 10⁻⁹, which signifies its high safety performance. The aluminum casing enhances durability, while integral LEDs provide local signaling for clear visibility of operational status. The system can function independently or in conjunction with a compatible safety control unit.Equipped with two normally open (NO) solid-state PNP safety outputs (OSSDs), it adheres to rigorous safety standards, achieving category 4 compliance, performance level PL e, and SIL 3 as outlined in EN/ISO 13849-1, EN/IEC 61508, and EN/IEC 61496-1/2. The operating temperature range spans from -30°C to +55°C, allowing for versatility in various environments, with selectable sensing distances of either 0 to 4 meters or 0 to 12 meters, depending on wiring configurations.