ATV312H055M3

Main

Commercial Status

Commercialised

Range of product

Altivar 312

Product or component type

Variable speed drive

Product destination

Asynchronous motors

Product specific application

Simple machine

Assembly style

With heat sink

Component name

ATV312

Motor power kW

0.55 kW

Motor power hp

0.75 hp

[Us] rated supply voltage

200...240 V (- 15...10 %)

Supply frequency

50...60 Hz (- 5...5 %)

Phase

3 phases

Line current

4.2 Afor 240 V

Line current

4.9 Afor 200 V, 5 kA

EMC filter

Without EMC filter

Apparent power

1.7 kVA

Maximum transient current

5.6 Afor 60 s

Power dissipation in W

43 W at nominal load

Speed range

1...50

Asynchronous motor control profile

Factory set : constant torque

Asynchronous motor control profile

Sensorless flux vector control with PWM type motor control signal

Electrical connection

L1, L2, L3, U, V, W, PA, PB, PA/+, PC/- terminal 0 in² (2.5 mm²) AWG 14

Electrical connection

Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6 terminal 0 in² (2.5 mm²) AWG 14

Supply

Internal supply for reference potentiometer (2.2 to 10 kOhm)at 10...10.8 V, Internal supply for logic inputsat 19...30 V,

Communication port protocol

CANopen

Communication port protocol

Modbus

IP degree of protection

IP41 on upper part

IP degree of protection

IP31 on upper part

IP degree of protection

IP21 on connection terminals

IP degree of protection

IP20 on upper part without cover plate

Option card

Profibus DP communication card

Option card

Modbus TCP communication card

Option card

Fipio communication card

Option card

DeviceNet communication card

Option card

CANopen daisy chain communication card

Complementary

Supply voltage limits

170...264 V

Network frequency limits

47.5...63 Hz

Prospective line Isc

5 kA

Continuous output current

3.7 Aat 4 kHz

Speed drive output frequency

0...500 Hz

Nominal switching frequency

4 kHz

Switching frequency

2...16 kHz adjustable

Transient overtorque

170...200 % of nominal motor torque

Braking torque

100 % without braking resistor

Braking torque

100 % with braking resistor continuously

Braking torque

150 % with braking resistorfor 60 s

Regulation loop

Frequency PI regulator

Motor slip compensation

Adjustable

Motor slip compensation

Automatic whatever the load

Motor slip compensation

Suppressable

Tightening torque

7.08 lbf.in (0.8 N.m) L1, L2, L3, U, V, W, PA, PB, PA/+, PC/-

Tightening torque

5.31 lbf.in (0.6 N.m) Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6

Insulation

Electrical between power and control

Analogue input number

3

Analogue input type

AI3 configurable current 0...20 mA, impedance 250 Ohm

Analogue input type

AI2 configurable voltage +/- 10 V, input voltage 30 V max, impedance 30000 Ohm

Analogue input type

AI1 configurable voltage 0...10 V, input voltage 30 V max, impedance 30000 Ohm

Sampling duration

LI1...LI6 4 ms discrete

Sampling duration

AI1, AI2, AI3 8 ms analog

Response time

R1A, R1B, R1C, R2A, R2B 8 ms discrete

Response time

AOV, AOC 8 ms analog

Linearity error

+/- 0.2 % output

Analogue output number

1

Analogue output type

AOV configurable voltage 0...10 V, impedance 470 Ohm, resolution 8 bits

Analogue output type

AOC configurable current 0...20 mA, impedance 800 Ohm, resolution 8 bits

Discrete input logic

(LI1...LI6) positive logic (source), 11 V (state 1)

Discrete input logic

(LI1...LI6) negative logic (source), > 19 V (state 0)

Discrete input logic

(LI1...LI4) logic input not wired,

Discrete output number

2

Discrete output type

(R2A, R2B) configurable relay logic NC, electrical durability 100000 cycles

Discrete output type

(R1A, R1B, R1C) configurable relay logic 1 NO + 1 NC, electrical durability 100000 cycles

Minimum switching current

R1-R2 10 mAat 5 V DC

Maximum switching current

R1-R2 on resistive load, 5 Aat 30 V DC, cos phi = 1, L/R = 0 ms

Maximum switching current

R1-R2 on resistive load, 5 Aat 250 V AC, cos phi = 1, L/R = 0 ms

Maximum switching current

R1-R2 on inductive load, 2 Aat 30 V DC, cos phi = 0.4, L/R = 7 ms

Maximum switching current

R1-R2 on inductive load, 2 Aat 250 V AC, cos phi = 0.4, L/R = 7 ms

Discrete input number

6

Discrete input type

(LI1...LI6) programmable, 24 V 0...100 mA with PLC, impedance 3500 Ohm

Acceleration and deceleration ramps

Linear adjustable separately from 0.1 to 999.9 s

Acceleration and deceleration ramps

S, U or customized

Braking to standstill

By DC injection

Protection type

Thermal protection motor

Protection type

Short-circuit between motor phases drive

Protection type

Overheating protection drive

Protection type

Overcurrent between output phases and earth (on power up only) drive

Protection type

Motor phase breaks drive

Protection type

Line supply phase loss safety function, for three phases supply drive

Protection type

Line supply overvoltage and undervoltage safety circuits drive

Protection type

Input phase breaks drive

Insulation resistance

>= 500 mOhmat 500 V DC for 1 minute

Local signalling

Four 7-segment display units CANopen bus status

Local signalling

1 LED red drive voltage

Time constant

5 ms for reference change

Frequency resolution

Display unit 0.1 Hz

Frequency resolution

Analog input 0.1...100 Hz

Type of connector

1 RJ45 Modbus/CANopen

Physical interface

RS485 multidrop serial link

Transmission frame

RTU

Transmission rate

4800, 9600 or 19200 bps Modbus

Transmission rate

10, 20, 50, 125, 250, 500 kbps or 1 Mbps CANopen

Number of addresses

1...247 Modbus

Number of addresses

1...127 CANopen

Number of drive

31 Modbus

Number of drive

127 CANopen

Marking

CE

Operating position

Vertical +/- 10 degree

Height

5.71 in (145 mm)

Width

2.83 in (72 mm)

Depth

5.2 in (132 mm)

Product weight

2.87 lb(US) (1.3 kg)

Environment

Dielectric strength

2880 V AC between control and power terminals

Dielectric strength

2040 V DC between earth and power terminals

Electromagnetic compatibility

Radiated radio-frequency electromagnetic field immunity test conforming to IEC 61000-4-3 level 3

Electromagnetic compatibility

Electrostatic discharge immunity test conforming to IEC 61000-4-2 level 3

Electromagnetic compatibility

Electrical fast transient/burst immunity test conforming to IEC 61000-4-4 level 4

Electromagnetic compatibility

1.2/50 µs - 8/20 µs surge immunity test conforming to IEC 61000-4-5 level 3

Standards

IEC 61800-3

Standards

IEC 61800-5-1

Product certifications

CSA

Product certifications

C-Tick

Product certifications

DNV

Product certifications

GOST

Product certifications

NOM

Product certifications

UL

Pollution degree

2

Protective treatment

TC

Vibration resistance

1.5 mm (f = 3...13 Hz) conforming to EN/IEC 60068-2-6

Vibration resistance

1 gn (f = 13...150 Hz) conforming to EN/IEC 60068-2-6

Shock resistance

15 gn 11 ms conforming to EN/IEC 60068-2-27

Relative humidity

5...95 % without dripping water conforming to IEC 60068-2-3

Relative humidity

5...95 % without condensation conforming to IEC 60068-2-3

Ambient air temperature for storage

-13...158 °F (-25...70 °C)

Ambient air temperature for operation

14...140 °F (-10...60 °C) with derating factor without protective cover on top of the drive

Ambient air temperature for operation

14...122 °F (-10...50 °C) without derating with protective cover on top of the drive

Operating altitude

3280.84...9842.52 ft (1000...3000 m) with current derating 1 % per 100 m

Ordering and Shipping Details

Category

22152 - ATV312 / ATV32 (.25 THRU 7.5 HP)

Discount Schedule

CP4B

GTIN

00785901594109

Nbr. of units in pkg.

1

Product availability

Stock - Normally stocked in distribution facility

Returnability

Y

Country of origin

ID

Offer Sustainability

Sustainable offer status

Green Premium product

RoHS (date code: YYWW)

Compliant - since 0913 -

RoHS (date code: YYWW)

Schneider Electric declaration of conformity

REACh

Reference contains SVHC above the threshold -

REACh

Go to CaP for more details

Product environmental profile

Available

Product environmental profile

Download Product Environmental Profile

Product end of life instructions

Available

Product end of life instructions

Download End of life manual

Contractual Warranty

Warranty period

18 months

Documents