8560710000

1 / 4

Description

RTD isolating transformer, Tension-clamp connection

Part Number: 8560710000

Get up to 90 days payment terms from 500+ suppliers
Reselling discounts up to 40%!

Send request for price

1

Payment methods:

Request a Quote and we will send you information on availability and price.

General Data

Accuracy: < 0.3 % of measured value
Configuration: DIP switch, Potentiometer
Current-carrying capacity of cross-connect.: ≤ 2 A
Galvanic isolation: 3-way isolator
Input/Output: configurable
Linearity: Yes
Power consumption: 830...880...980 mW at IOUT = 20 mA
Rail: TS 35
Step response time: fast/slow: 2-/3-/4-conductor: 1.2 s/2.2 s; potentiometer: 0.5 s/1.1 s
Temperature coefficient: Measuring range ≥ 200 K: ≤ 200 ppm/K100 K <= measuring range < 200 K: <= 250 ppm/K40 K <= measuring range < 100 K: ≤ 400 ppm/K
Voltage supply: 24 V DC ± 20 %

Probability Of Failure

MTTF: 270 Years

Approvals

Approvals: CE, CULUS, EAC, GERMLLOYD
ROHS: Conform
UL File Number Search: E141197

Dimensions And Weights

Length: 92.4 mm
Length (inches): 3.638 inch
Width: 17.5 mm
Width (inches): 0.689 inch
Depth: 112.4 mm
Depth (inches): 4.425 inch
Weight: 100 g
Net weight: 140 g

Connection Data

Type of connection: Tension-clamp connection
Stripping length, rated connection: 7 mm
Clamping range, rated connection: 1.5 mm²
Clamping range, min.: 0.5 mm²
Clamping range, max.: 2.5 mm²

Tender Specification Sheets

Long specification: RTD measurement isolating transformer; configured with DIP switchesRTD measurement isolating transformer in 17.5 mm width with external power supply,for transmitting and isolating PT100 and Ni100 2-/3-/-4-wire signals, resistors and potentiometer signals.Analogue DC signals 0(4) to 20 mA / 0 to 10 V are available on the output side.Zero/span compensation with potentiometer. Add-on housing for TS35 rail mountingDimensions: L/W/H 92.4/ 17.5/ 112.4 mmTension-clamp connection / Nominal cross-section 1.5 mm2Protection degree: IP 20 Input PT100, Ni100 2-/3-/4-wire Resistance 0...450 Ohm/ Potentiometer100 Ohm...100 kOhm Output 0/4...20 mA 0...10 V Load resistance < 600 Ohm/ Strom/> 1 kOhm/ voltageTransmission error < 0,8 % v. E. ( RTD) typ. 200 ppm / °CAuxiliary power 24 VDC +/- 25 %Power loss approx. 0.9 WAmbient temperature range 0°C...+55 °CIsolation EN 50178, 3-way isolation up to 4 kV AC/DC of all circuits against each otherTest voltage 4 kV input against output against auxiliary powerRated voltage 300 V AC/DC at overvoltage category III and pollution degree 2Approvals cULus, cULusEX, GLType WAZ5 PRO RTD
Short specification: RTD measurement isolating transformer; configured with DIP switchesRTD measurement isolating transformer in 17.5 mm width with external power supply,for transmitting and isolating PT100 and Ni100 2-/3-/-4-wire resistor signals and potentiometer signals. Analogue DC signals 0(4) to 20 mA / 0 to 10 V are available on the output side. Zero/span compensation with potentiometer.

Input

Number of inputs: 1
Sensor: PT100/2-/3-/4-wire, Ni100/2-/3-/4-wire, potentiometer: min. 0–100 Ω, max. 0–100 kΩ, resistance: 0–450 Ω
Line resistance in measuring circuit: 50 Ω for 3- and 4-conductor
Temperature input range: Configurable, PT100: -200°C…850 °C, NI100: -60°C…+250 °C

Classifications

ETIM 6.0: EC002919
ETIM 7.0: EC002919
EClass 9.0: 27-21-01-29
EClass 9.1: 27-21-01-29
EClass 10.0: 27-21-01-29
UNSPSC: 30-21-18-01

Output

Number of outputs: 1
Output voltage, note: 0...10 V
Output current: 0...20 mA, 4...20 mA
Wire break detection: LED flashing (output value: > 20 mA, >10 V)
Fine adjustment: ≥ ± 5 %, Version 1 and later: ≥ 12.5 % / potentiometer: 12.5%...25%
Load impedance voltage: ≥ 1 kΩ
Load impedance current: ≤ 600 Ω
Offset voltage: max. 0.05 V
Offset current: max. 100 µA
Status indicator: Module active: LED on/ wire breakage: LED flashing/Error: LED off

Product Information

Product information: This product will soon be replaced by a new product.Please do not use with new systems. Please contact our technical support.

Environmental Product Compliance

REACH SVHC: Lead 7439-92-1

Insulation Coordination

Clearance & creepage distances: ≥ 3 mm
EMC standards: EN 55011, EN 61000-6
Galvanic isolation: 3-way isolator
Impulse withstand voltage: 4 kV
Insulation voltage: 2 kVeff / 5 s
Insulation voltage input or output/rail: 4 kVeff / 1 min.
Insulation voltage input or output/supply: 2 kVeff / 5 s
Pollution severity: 2
Rated voltage: 300 V
Surge voltage category: III

Temperatures

Operating temperature, max.: 55 °C
Operating temperature, min.: 0 °C
Storage temperature, max.: 85 °C
Storage temperature, min.: -20 °C
Operating temperature: 0 °C...55 °C
Storage temperature: -20 °C...85 °C

Ratings Iecex/Atex/Cul

Certificate no. (cULus): E141197

Related products